[ Pobierz całość w formacie PDF ]

not to strike the crown of the muzzle with the handle
CHAMBER, MAGAZINE OR ACTION/FEED
end of the rod. Damage to this area can affect the
AREAS.
accuracy of the rifle.
You should clean your Model 1892 after every day of
2. Inspect the chamber and bore for brass, copper,
shooting and more often if it becomes excessively
lead and powder fouling. A normal amount of powder
dirty. A minimum cleaning includes wiping down the
residue can be expected and is not serious. It can usu-
30 31
7. Wipe all wood surfaces.
ally be removed by repeating step one, using a patch
saturated with solvent. If or when fouling should
8. When transporting only, place your Model 1892 in
become heavy, it can be removed with a brass bore
a quality protective case to prevent scratches and
brush. Dip or spray the brush with solvent and scrub
dents. Store in a dry place to prevent corrosion. Store
the chamber and bore until the fouling is removed.
away from children. Make sure your gun is unloaded
To prevent brass bristles from breaking off, the brush
and always store ammunition separately.
should be pushed completely through the bore before
OTHER CLEANING SUGGESTIONS 
being withdrawn.
" Never pour large quantities of oil into the receiver
3. After fouling has been removed the bore should be
or other parts. It can drain down to the wood and
wiped dry. Then pass a slightly oiled patch through
soften it  and cause permanent damage and loosen-
the bore, for preservation. A fine, light gun oil is rec-
ing of the stock.
ommended.
" After extended periods of heavy use, your gun
4. Wipe all exposed metal surfaces of the receiver,
should be taken to a qualified gunsmith to have the
forearm and barrel with a clean rag. Finger marks
action disassembled for professional cleaning and
should be removed because they provide a place
lubrication.
where moisture can accumulate. Any dried oil in the
receiver area should also be removed.
NEVER ATTEMPT TO TAKE YOUR MODEL
1892 APART FURTHER THAN EXPLAINED
5. Then lightly oil your gun at the points described
IN THIS MANUAL.
under  Oiling the Action explained earlier in this
manual. Ordinary good judgment will, of course, indi-
This is a specialized, finely fitted mechanism. You
cate that the metal of the gun should receive a light
may permanently mar it by attempting to disassemble
film of oil any time the rifle has been exposed to
the inner mechanism assemblies. If further disassem-
weather or handling. Remember, the polished, finely
bly for service or cleaning is required, take your gun
fitted surfaces of the receiver and action mechanisms
to a U. S. Repeating Arms Company recommended
must always have a thin film of oil. Make sure that
Service Center or a competent gunsmith as explained
the surfaces of the breech block, lever components
under  Service or Repair.
and feed mechanism parts are especially clean and
lightly oiled with a high quality gun oil. Do not use
pure silicone or lanolin.
6. INSPECT THE BARREL AND CHAMBER.
TO MAKE CERTAIN THAT NO PATCHES
HAVE BEEN INADVERTENTLY LEFT IN
THEM. Remove any that remain.
32 33
QUESTIONS
ORDERING PARTS
If you have other questions about Winchester rifles
To order parts, please write our parts department and
and shotguns, call or write our Customer Service
furnish the following: your name, address, and tele-
Department:
phone number. Also specify the model and serial
number of your gun. When we receive your request,
Customer Service
we will send an order form and a parts breakdown
U.S. Repeating Arms Company, Inc.
with prices.
275 Winchester Avenue
Morgan, Utah 84050-9333
Write to:
Phone: 1-800-945-5237
Parts Department
U.S. Repeating Arms Company, Inc.
WINCHESTER-GUNS.COM
275 Winchester Avenue
New Haven, Connecticut 06511-1970 U.S. Repeating Arms Company offers an information
resource for you on the world wide web.
CAUTION: PARTS ARE MADE FOR
WINCHESTER BRAND FIREARMS MANU- " List of authorized repair centers.
FACTURED BY OR FOR U.S. REPEATING
" Customer service information.
ARMS COMPANY, INC., AND SHOULD NOT
" Answers to many technical and historical
BE USED IN OTHER GUNS EVEN THOUGH
questions.
MODELS MAY BE SIMILAR. IMPROPERLY
FITTED PARTS MAY BE DANGEROUS. " Links to helpful sites.
Go to: www.winchester-guns.com
SERVICE OR REPAIR
If your Winchester firearm should ever need repair or
service, please utilize one of the world-wide network
of U.S. Repeating Arms Company Authorized Repair
Centers for Winchester firearms. If you have any
questions about how to obtain service for your
Winchester firearm, call or write the Authorized
Repair Center (ARC) nearest you. A list of ARCs is
packaged with your new gun. If you need to obtain a
new list of ARCs call us at:
1-203-789-5000
34 35 [ Pobierz całość w formacie PDF ]